Saiken Pump Industry introduces ISG vertical pipeline centrifugal pump to you

The ISG type single-stage single-suction pipeline centrifugal pump has a vertical structure with the same inlet and outlet diameters and located on the same centerline. It can be installed in the pipeline like a valve. It has a compact and beautiful appearance, small footprint, and low construction investment. If a protective cover is added, it can be used outdoors.
The impeller is directly installed on the extended shaft of the motor. The axial size is short, the structure is compact, and the bearing configuration of the pump and the motor is reasonable, which can effectively balance the radial and axial loads generated by the operation of the pump, thereby ensuring the smooth operation of the pipeline centrifugal pump. Low vibration and low noise.
The shaft seal adopts a mechanical seal or a combination of mechanical seals, adopts imported titanium alloy seal rings, medium-sized high temperature resistant mechanical seals and adopts hard alloy materials, wear-resistant seals, which can effectively extend the service life of mechanical seals.
Easy installation and maintenance, no need to dismantle the pipe road system, all the rotor parts can be drawn out by removing the nut of the pump joint base.
The series and parallel operation modes of pumps can be adopted according to the requirements of use, that is, the needs of flow and head.
The vertical and horizontal installation of the pump can be adopted according to the requirements of the pipeline layout.
Vertical pipeline pump manufacturers and suppliers

Brief introduction of ISG vertical pipeline pump

ISG type pipeline centrifugal pump is designed and manufactured according to the performance parameters of IS type centrifugal pump and pipeline pump, referring to ISO2858 and the new national pipeline centrifugal pump standard JB/T53058-93. The pump is optimized and designed by domestic advanced hydraulic model. At the same time, based on the use temperature and medium, the hot water pump pipeline centrifugal pump, high temperature pipeline centrifugal pump, chemical pump, oil pump, etc. are derived from the ISG type, which are the current national standard products to be promoted.

Product Usage

The ISG type pipeline centrifugal pump is used to transport clean water and other liquids with physical and chemical properties similar to clean water. It is suitable for industrial and urban water supply and drainage, high-rise building pressurized water supply, garden irrigation, fire pressurization and equipment supporting, operating temperature T: ≤80°C.
IRG (GRG) type hot water (high temperature) circulating pump is widely used in energy, metallurgy, chemical industry, textile, paper, and hotels and restaurants, such as boilers for high-temperature hot water pressurized circulation and urban heating system circulation pumps, IRG operating temperature T: ≤120℃, GRG operating temperature T: ≤240℃.
The IHG type pipeline chemical pump is used to transport liquids that do not contain solid particles, are corrosive, and have a viscosity similar to water. It is suitable for petroleum, chemical, metallurgical, electric power, papermaking, food, pharmaceutical and synthetic fiber sectors. The use temperature is T ：-20℃-120℃.
YG pipeline oil pump is used to transport petroleum products such as gasoline, diesel, kerosene, etc. The operating temperature is T: -20℃-120℃.

Working conditions

Suction pressure ≤1.0Mpa, or pump system high working pressure ≤1.6Mpa, that is, pump suction port pressure + pump head ≤1.6Mpa, pump static pressure test pressure is 2.5Mpa, please indicate the system working pressure when ordering. When the working pressure of the pump system is greater than 1.6Mpa, it should be stated separately when ordering. In order to make the pump’s flow-through parts and connection parts use cast steel materials.
Ambient temperature <40℃, relative humidity <95%.
The volume content of solid particles in the conveyed medium does not exceed 0.1% of the unit volume, and the particle size is less than 0.2mm.
Note: If the medium used is with fine particles, please specify when ordering so that wear-resistant mechanical seals can be used.

ISG type single-stage single-suction pipeline centrifugal pump

The ISG type single-stage single-suction pipeline centrifugal pump is an excellent hydraulic model selected by the scientific and technological personnel of SAIKEN Pump Industry and the United Nations internal water pump experts. It adopts the performance parameters of the IS type centrifugal pump and is designed by ingenious combination on the basis of general vertical pumps. . At the same time, based on the ISG vertical pipeline pump, suitable for hot water, high temperature, corrosive chemical pumps, and oil pumps are dispatched according to the use temperature and medium. This series of products have the advantages of high efficiency, energy saving, low noise and reliable performance. Working conditions:

The suction pressure is ≤1.0MPa, or the maximum working pressure of the pump system is ≤1.6MPa, that is, the pump suction inlet pressure + pump head ≤1.6MPa, and the pump static pressure test pressure is 2.5MPa. Please specify the system working pressure when ordering. When the working pressure of the pump system is greater than 1.6MPa, it should be separately stated when ordering, so that the flow-through part and the connecting part of the pipeline centrifugal pump are made of cast steel.
Ambient temperature <40℃, relative humidity <95%.
The volume content of solid particles in the conveyed medium does not exceed 0.1% of the unit volume, and the particle size is less than 0.2mm.
Note: If the medium used is with fine particles, please specify when ordering so that the manufacturer can use wear-resistant mechanical seals.

ISG type single-stage single-suction pipeline centrifugal pump is used to transport clean water and other liquids with physical and chemical properties similar to clean water. It is suitable for industrial and urban water supply and drainage, high-rise building pressurized water supply, garden sprinkler irrigation, fire pressurization, and long-distance transportation. , HVAC refrigeration cycle, bathroom and other cold and warm water cycle pressurization and equipment supporting, the use temperature T <80 ℃.

The working principle and application of self-priming magnetic drive pump

The pump uses static seals instead of dynamic seals, so that the flow parts of the pump are in a completely sealed state, which solves the problems of running, emitting, dripping and leaking that cannot be avoided by other pump mechanical seals. The materials of the pump body and flow parts are all adopted. Made of corrosion-resistant stainless steel, corundum ceramics, tetrafluorographite and other materials.

The pump not only has the function of a magnetic drive pump, but also integrates self-priming. It does not need a bottom valve and irrigation water. The self-priming height is 4m. It can be widely used in petroleum, chemical, pharmaceutical, electroplating, printing and dyeing, food, scientific research and other units to pump acid. , Alkali, oil and rare precious liquids, venoms, volatile liquids, and circulating water equipment, especially for the pumping of leaky, flammable, and explosive liquids.

The fluoroplastic self-priming magnetic drive pump adopts a direct-connected motor structure and is supported by a middle bracket. The inner and outer magnets are made of high-performance magnetic material “neodymium iron boron”. The isolating sleeve is used to eliminate the magnetic eddy current loss of general magnetic drive pumps. The liquid part of the pump is Fluoroplastic, but the outer shell is made of metal material, so the pump body can bear the weight of the pipeline and withstand mechanical shocks.

　The working principle of the self-priming magnetic pump: The pump adopts an external-mixed axial return water pump body structure. The pump body is composed of a liquid suction chamber, a liquid storage chamber, a volute, a return hole, a gas-liquid separation chamber, etc. The structure is shown in the schematic diagram. After the pump is started, under the action of centrifugal force, the remaining liquid in the suction chamber and the air in the liquid inlet pipe are stirred by the impeller to form a water-gas mixture. The mixture enters the gas-liquid separation chamber through the volute. The water is separated, and the air is discharged from the outlet of the pump, and the liquid returns to the pump through the return hole. After multiple cycles, the air in the inlet pipe is drained, so that a certain degree of vacuum is formed in the pump to achieve self-priming. The protector for the pump can be configured to automatically cut off the power when the pump is idling or overloaded, so as to protect the internal components of the pump or the motor from being damaged due to the idling of the pump or the overload of the motor. Applicable temperature: -30℃～200℃

Purpose of self-priming magnetic drive pump: The pump has compact structure, beautiful appearance, small size, low noise, low noise, reliable operation, convenient use and maintenance, and can be widely used in petroleum, chemical, pharmaceutical, electroplating, printing and dyeing, food, and scientific research. Units such as pumping acids, alkalis, oils and rare precious liquids, venoms, volatile liquids, as well as supporting equipment for circulating water, especially the pumping of leaky, flammable, and explosive liquids.

What is the difference between a centrifugal pump and a self-priming pump?

Should you choose a centrifugal pump or a self-priming pump? I must have a certain understanding of centrifugal pumps and self-priming pumps. In simple terms, compared with self-priming pumps, self-priming pumps have a certain self-priming ability. The pump does not. In normal operation, the self-priming pump has a suction stroke of 6-8 meters. The centrifugal pump has no suction stroke. Only when the bottom valve is installed, it has a certain self-priming ability. SAIKEN below is for you Detailed introduction

The specific difference between centrifugal pump and self-priming pump is as follows:

The composition is different: the self-priming pump is composed of a suction chamber, a liquid storage chamber, a scroll chamber, a liquid return hole, a gas-liquid separation chamber, etc.; the basic structure of a centrifugal pump is composed of six parts: the impeller and the pump body , Pump shaft, bearing, sealing ring, stuffing box.
Different advantages: the self-priming pump is simple to operate, stable in operation, convenient to maintain, high in efficiency, long life, and self-priming; the centrifugal pump has a wide flow range and a wide lift range, which can be applied to certain corrosive liquids. Shock absorption, low vibration, simple and convenient equipment installation. 　　3. The working principle is different: the centrifugal pump works by the centrifugal movement of the water due to the rotation of the impeller; the working principle of the self-priming pump is that the pump casing is filled with water before the pump is started (or the pump casing itself contains water). After starting, the impeller rotates at a high speed to make the water in the impeller channel flow to the volute. At this time, the inlet forms a vacuum, so that the water inlet check door opens, and the air in the suction pipe enters the pump and reaches the outer edge through the impeller channel.

Concentrated sulfuric acid magnetic drive pump product overview, application and material selection　

1: Overview of concentrated sulfuric acid magnetic drive pump products

　　 Concentrated sulfuric acid magnetic pump, also known as concentrated sulfuric acid magnetic unloading pump, concentrated sulfuric acid magnetic unloading pump, no leakage, no shaft seal, suitable for strong acid and alkali medium transportation. It can achieve no leakage, will not cause the leakage of chemical liquid, and effectively avoid environmental pollution. It can be used to transport a variety of chemical acid and alkali liquids, and has great advantages when transporting valuable liquids and liquids with strong acid and alkali resistance. The operating temperature can reach 75 when the CFRPP material is selected, and it can reach 90 when the PVDF material is selected, depending on the nature of the chemical liquid.

　　 2: Application of concentrated sulfuric acid magnetic drive pump in water treatment

　　 Concentrated sulfuric acid magnetic pump adopts no shaft seal design, acid and alkali resistance, no leakage. It is suitable for wastewater treatment or the transportation, circulation, unloading, dosing, spraying and other processes of various strong and weak acids, alkali media, organic solvents and chemical solutions. Mainly used in chemical wastewater, high ammonia nitrogen wastewater, electroplating wastewater, oily wastewater, food wastewater, photovoltaic wastewater, printing and dyeing wastewater and other fields.

　　3: Application of concentrated sulfuric acid magnetic pump in chemical media

Concentrated sulfuric acid magnetic pumps are commonly used in materials such as pp (polypropylene), frpp (reinforced polypropylene), and pvdf (fluoroplastics). They are mainly used for chemical medium transportation, unloading, circulation, dosing, etc., and can handle any concentration of acid, alkali, Salt and organic solvents and other media and sewage. Including but not limited to: sulfuric acid, hydrochloric acid, nitric acid, lye, methanol, ethanol, ammonia, salt water, sea water, sodium hypochlorite, sodium acetate, hydrogen peroxide, phosphate, etc.

　　 Four: Selection of commonly used materials for concentrated sulfuric acid magnetic pump

60% concentration (normal temperature, high temperature) uses PP material, 98% concentration (normal temperature) uses PVDF material as one of the strong corrosive media. The corrosion of sulfuric acid with different concentrations and temperatures is quite different. For the concentration above 80%, the temperature Concentrated sulfuric acid less than 80, engineering plastics have better sulfuric acid resistance, and engineering plastic pumps are a more economical choice. For high-temperature sulfuric acid media, fluoroplastics or stainless steel are mostly used.

What should I pay attention to when using acid and alkali resistant magnetic drive pump?

Acid and alkali resistant magnetic drive pump is a new type of pump that uses the working principle of magnetic coupling to transmit torque without contact. When the motor drives the outer magnetic rotor to rotate, the magnetic field drives the inner magnetic rotor and the impeller to rotate synchronously, so as to achieve For the purpose of pumping liquid, since the liquid is enclosed in a stationary isolating sleeve, it is a fully sealed, leak-free pump type.

Pay attention to the following points when using acid and alkali resistant magnetic drive pump:

　　 1. Acid and alkali resistant magnetic pump should be checked at regular intervals (about 1000h). The insulation resistance of the acid and alkali resistant magnetic pump should be not less than 0.5MΩ. If it does not meet the requirements, it should be dried.

　　2. Before use, check the cables, switches, and electric shock protectors. The switches and other electrical appliances should work normally, the cables are not damaged, and the cables should be carefully identified. The yellow and green two-color wires are grounding wires to prevent leakage and electric shock accidents.

　　 3. When the acid and alkali resistant magnetic pump enters or discharges water, the power must be cut off, and then the rope tied to the hoisting ring must be pulled. The cable cannot be used as a pull rope.

4.The acid and alkali resistant magnetic pump cannot be buried in the river mud. If there are many water and leather debris in the water, the acid and alkali resistant magnetic pump should be placed in the basket or basket, and then the basket or basket should be placed in the water.

　　 5. When the acid and alkali resistant magnetic pump is tested outside the water (such as to determine the direction of rotation), it shall not exceed 1 minute to prevent the motor from heating and burning.

Fluoroplastic magnetic pump manufacturers and suppliers

What are the advantages of fluoroplastic chemical magnetic pump?

Fluoroplastic chemical magnetic pump is a branch of the magnetic pump field, and is a new product that applies the working principle of permanent magnet coupling to centrifugal pumps.

　　 PP chemical magnetic pump is composed of three parts: pump, magnetic drive and motor. The magnetic drive of the fluoroplastic chemical magnetic pump consists of an outer magnetic rotor, an inner magnetic rotor and a non-magnetic isolation sleeve. The working principle of the magnetic pump is that when the motor drives the outer magnetic rotor to rotate, the magnetic field can penetrate the air gap and non-magnetic materials, and drive the inner magnetic rotor connected to the impeller to rotate synchronously, realize the non-contact and synchronous transmission of power, and will easily leak the power. The sealing structure is transformed into a static sealing structure with zero leakage.

　　The advantages of fluoroplastic chemical magnetic pump are:

　　 1. Good sealing effect, as long as the isolating sleeve is not damaged, there will be no leakage.

　　2. The motor has a strong anti-overload capability. Because it is a magnetic drive, the inner shaft will not cause the motor’s outer shaft to jam.

　　3. It can be better applied to the transportation of flammable, explosive, toxic, harmful and corrosive media.

　　 4. Easy to disassemble.

Fluoroplastic magnetic pump manufacturers and suppliers

What are the main applications of fluoroplastic magnetic pumps?

The main application range of fluorine plastic magnetic pump:

Chemical industry: sodium carbonate chemical industry (production of hydrochloric acid, abalone, secondary chemicals), production of fluoride, chemical fertilizers, gas absorption tower chemical industry reaction liquid circulation, oil refining (sulfuric acid), recovery of waste acids And the transportation of strong acids between regeneration systems, chemical plants and transportation vehicles.

　　Pharmaceutical industry: production of luminescent chemicals (EL) for semiconductors, pesticides, medicines, and water treatment chemicals.

　　 Electroplating industry: circulating filtration of various electroplating solutions.

　　Photographic industry: instant photographic system, X-ray film, black and white, color, three-dimensional photo development.

　　Electrical appliance industry: production of electrolytic capacitors (etching of aluminum film), transportation of electrolyte in the manufacturing process of a thousand-cell and harmonious battery; etching of circuit boards; transportation of high-purity chemical solutions in the production of semiconductors.

　　 Metal industry: alumina film treatment equipment; wire drawing, degreasing and pickling in steel rolling; degreasing and pickling treatment before painting on vehicles; production of titanium oxide and rare earth elements, etc.
Mining industry: metal smelting (transportation and circulation of electrolyte), washing treatment of waste liquid.

　　 Food industry: production of gluconic acid (hydrochloric acid), refining of edible oil (sulfuric acid), canned fruit industry (salt).

　　 medical treatment: artificial kidney, heart and lung, ultrasonic cleaning machine and various medical equipment.

　　Water treatment: clean wash ion exchange resin; pure water production equipment; seawater desalination equipment.

　　Pollution control: adding sewage treatment chemicals to the chemical tank, collecting and transporting waste liquid, and exhaust gas absorption equipment (deodorizing device, desulfurization before exhaust gas).

　　Others: Used in silver recovery, wafer manufacturing, experimental plants, refrigerators, beverage machines, living boilers, heat exchangers, solar systems, bleaching and dyeing, laser systems and other fields, and recycling use in fountains, fish ponds, and ornamental fish tanks.

Fluoroplastic magnetic pump manufacturers and suppliers

Self-priming pump manufacturers to introduce the following pvdf self-priming pump

Self-priming pump manufacturers to introduce the following pvdf self-priming pump：
Alias: sewage lift pump, corrosion-resistant self-priming pump, big head pump, self-priming sewage pump, fluoroplastic self-priming pump
Purpose: Suitable for pumping, recycling, and discharging all chemical liquids, sewage, etc. containing acid and alkali corrosive ingredient
Flow: 0–200m3/h Head: 0-40m Power: 0.37-40KW

Acid and alkali corrosion resistance, no leakage, suitable for chemical liquid, treatment waste liquid and acid and alkali liquid transportation and recycling operations; use FRPP, PVDF material injection molding, strong corrosion resistance, strong acid and strong alkali; applicable temperature: FRPP-75 Below ℃, below PVDF-90℃; Unique shaft seal design, adopts self-cooling design, no additional cooling is required; Self-priming design: strong self-priming; a bottom valve must be installed at the inlet to prevent the inhalation of foreign objects and ensure liquid lifting;
Acid and alkali resistant self-priming pumps are suitable for: sewage, waste gas, electroplating, painting, circuit boards, chemical plants, photovoltaics, diamond wires and other fields

The motor is stable, effective, and has a long service life. The shaft seal cover and the foot are integrally formed, no leakage, and easy to install. The integrally formed self-priming barrel, PRPP material, no solder joints, more corrosion resistance, external screws to avoid corrosion

pvdf self-priming pump manufacturers and suppliers